Step 1: Check the Steering Wheel Lock

• Ensure the Steering Wheel is Not Locked: Sometimes, the steering wheel may lock, preventing the key from turning. Firmly grip the wheel and gently turn it left and right while attempting to turn the key in the ignition. This may release the lock and allow the key to turn.

Step 2: Inspect the Key for Damage

• Examine the Key: Look for any visible signs of wear, bending, or damage. If the key is worn or damaged, it may need to be replaced with a new one from a Ford dealer or a locksmith.

Step 3: Lubricate the Ignition Cylinder

• Use Graphite or Silicone Spray: Spray a small amount of graphite or silicone lubricant into the ignition cylinder. Insert and remove the key several times to distribute the lubricant evenly. Avoid using oil-based lubricants as they may attract dirt and debris.

Step 4: Check the Battery

• Test the Battery: A weak or dead battery can cause the ignition system to malfunction. Ensure the battery is fully charged or try jump-starting the car to see if this resolves the issue.

Step 5: Inspect the Ignition Cylinder

• Look for Obstructions: Examine the ignition cylinder for foreign objects or debris that might be blocking the key from turning. If necessary, gently clean the cylinder using compressed air or a soft brush.

Step 6: Replace the Ignition Cylinder (if needed)

• Follow Detailed Instructions in Our Manual: If the ignition cylinder is worn or damaged, it may need to be replaced. Our workshop manual provides step-by-step guidance on removing and installing a new ignition cylinder.

Call to Action:
Our Workshop Service & Repair Manual offers detailed guidance on troubleshooting and fixing ignition issues. It provides in-depth illustrations and step-by-step instructions to ensure you can resolve this problem efficiently.

Step 1: Identify Symptoms of Transmission Failure

• Notice Unusual Sounds: Listen for any grinding, whining, or clunking noises while driving, especially during gear shifts. These sounds may indicate transmission problems.
• Observe Gear Shifting Issues: Pay attention to any hesitation, slipping, or hard shifts between gears. If the vehicle struggles to shift smoothly, the transmission may need attention.

Step 2: Check Transmission Fluid Level and Quality

• Inspect Fluid Levels: Check the transmission fluid level using the dipstick. Ensure the fluid is at the proper level and appears clear and free of contaminants.
• Evaluate Fluid Condition: Healthy transmission fluid should be bright red and have a sweet odor. If it appears dark or burnt, it may be time for a fluid change.

Step 3: Perform a Transmission Fluid Change

• Follow Our Manual for Guidance: Our manual provides a detailed procedure for changing the transmission fluid, including draining old fluid, replacing the filter, and refilling with new fluid.

Step 4: Examine the Transmission for Leaks

• Inspect for Leaks: Check for any visible leaks under the vehicle. Common areas for leaks include the transmission pan gasket and seals. Repair any leaks found to prevent further damage.

Step 5: Test the Transmission Solenoid and Sensors

• Use Diagnostic Tools: Utilize an OBD-II scanner to identify any fault codes related to the transmission solenoid or sensors. Our manual explains how to interpret these codes and address the underlying issues.

Step 6: Seek Professional Assistance

• Consult a Transmission Specialist: If you're unable to resolve the issue, consult a professional mechanic specializing in transmission repairs for further diagnosis and repair.

Call to Action:
Our Workshop Service & Repair Manual provides comprehensive guidance on diagnosing and fixing transmission issues, from fluid changes to solenoid testing. Equip yourself with the knowledge to tackle transmission problems with confidence.

Step 1: Identify Signs of Engine Failure

• Look for Warning Lights: Check the dashboard for any warning lights, such as the check engine light or oil pressure warning. These lights may indicate underlying engine issues.
• Monitor Engine Performance: Pay attention to any unusual noises, vibrations, or loss of power while driving. These symptoms can signal potential engine problems.

Step 2: Conduct a Visual Inspection of the Engine

• Inspect for Leaks or Damage: Check for oil or coolant leaks, cracked hoses, or damaged components within the engine bay. Address any visible issues immediately.

Step 3: Check Engine Oil Level and Quality

• Examine Oil Levels: Use the dipstick to check the engine oil level. Ensure it’s at the proper level and appears clean and free of contaminants.
• Evaluate Oil Condition: Healthy engine oil should be clear and amber-colored. If it appears dirty or has a burnt smell, it may be time for an oil change.

Step 4: Perform a Compression Test

• Assess Engine Compression: Use a compression tester to evaluate the engine’s compression levels. Our manual provides detailed instructions on conducting this test and interpreting the results.

Step 5: Address Fault Codes

• Use Diagnostic Equipment: Utilize an OBD-II scanner to identify any engine-related fault codes. Our manual offers guidance on interpreting these codes and addressing the underlying issues.

Step 6: Repair or Replace Damaged Components

• Follow Our Manual for Detailed Repair Instructions: Depending on the diagnosis, repair or replace damaged engine components as needed. Our manual covers everything from gasket replacements to complete engine overhauls.

Step 7: Seek Professional Assistance

• Consult a Qualified Mechanic: If engine failure persists, consult a professional mechanic specializing in engine repairs for further diagnosis and repair.

Call to Action:
Our Workshop Service & Repair Manual provides comprehensive guidance on diagnosing and fixing engine issues, including compression testing, fault code analysis, and detailed repair instructions. Arm yourself with the expertise to tackle engine problems effectively.

Description: This code signifies a lack of switching in the downstream oxygen sensor, indicating a lean condition.

Solution:

Examine the Exhaust System: Check for leaks or damage in the exhaust system that may affect the oxygen sensor readings.

Test the Downstream Oxygen Sensor: Use a diagnostic tool to test the sensor’s functionality and replace it if faulty.

Follow Our Manual for Detailed Repair Instructions: Our manual offers comprehensive instructions for diagnosing and resolving sensor-related issues.

Code P1154: Bank 2 Fuel Control Shifted Rich

Description: This code indicates that the fuel control system on bank 2 has shifted rich, possibly due to a malfunctioning fuel injector or a faulty oxygen sensor.

Solution:

Inspect Fuel Injectors: Check for clogs or leaks in the fuel injectors. Clean or replace as needed.

Test Oxygen Sensors: Verify the functionality of oxygen sensors using a diagnostic tool. Replace if necessary.

Consult Our Manual for Detailed Procedures: Our manual provides step-by-step instructions for inspecting and repairing fuel control components.

Additional Fault Codes:

P1155: Alternative Fuel Controller Activated MIL

Solution: Inspect the alternative fuel system for issues and refer to our manual for detailed diagnostic procedures.

P1156: Fuel Select Switch Malfunction

Solution: Test the fuel select switch for proper function and replace it if necessary, following the instructions in our manual.

P1158: Lack of HO2S22 Switch - Sensor Indicates Rich

Solution: Check the downstream oxygen sensor and exhaust system for issues, utilizing our manual for guidance